That being said, even when drilling in the center of a tile, results can definitely vary depending on the material you’re drilling, the quality of your drill bits, and your drilling technique. The closer to the center of the tile you drill, the safer you are in this regard. Drilling close to the edge of a tile can be more likely to cause the tile to break around the area you’re drilling. Step 6: Change the Bit When You Hit the Wall If you want to increase the lifespan of your tools, then you need to drill slowly, don’t put too much pressure, and lubricate the drill with cool water. They will continue to work even when they heat, as long as you allow them to cool down from time to time. Not to mention, you’re preventing the water from pouring down the wall and all over the floor.Ī short note here: unlike carbide drill bits, which stop the second they overheat and need to be kept cool at all times, diamond bits are not as high-maintenance. That way, you’re not only preventing the drill from overheating, but you are also catching the dust and debris produced by the tile. Just make sure not to pour water into the motorized section of the drill.Īnother trick you can use to keep the drill cool is holding a wet sponge under it. If you’re on your own and can’t hold the drill bit in one hand, the wood pattern in the other, and cool the drill bit at the same time, then you can stop from time to time and spray some water on it. Use a small wet sponge to cool down the drill bit and prevent it from overheating. One of the secrets to drilling a hole through tile is keeping everything cool. Otherwise, you will break through the tile and create cracks. In reality, you will only overheat everything and create vibrations that could damage the surface.Īpply constant pressure, but not too much. Don’t make the mistake of believing that going full-speed is more effective. Take your time – it might take a while before you penetrate the hard glazed surface. One of the most important things you need to keep in mind is that drilling through tile is a task that requires a lot of patience. If you rush through the process, you might end up damaging all of your hard work. But, this also makes them resistant to drilling. The problem with tiles (although, we’re not sure if we can call this a problem) is that they are designed to withstand a lot of abuse. Once the surface is marked or you have your wooden template in place, it’s time to start drilling. This is the part where you will really learn how to drill through tile. Place it over the drill hole and hold it firmly with your free hand. Cut a hole through the wood, making sure it’s the same size as the drill bit you will be using. If you have more than one hole to drill and you don’t want to repeat this process over and over again, then you could create a template with a block of wood. That way, you will have enough surface traction when you start drilling. Measure it again after placing the masking tape to ensure that you didn’t misplace the hole. Measure the area, mark it with an X, and place the masking tape. One simple trick you can use to create some tension is to use masking tape over the area where you want to drill the hole. One wrong move and you’ll scratch or, even worse, crack the tile. If you’ve ever tried to drill a hole through tiles, then you probably know that the bits tend to slip around on the surface, making it difficult to hold them in place. If you don’t have the tools you need for drilling into tile, at RUBI you can find a complete range of drill bits that will help you tackle this task successfully! Step 3: Measure and Mark the Area For this and harder materials, you will need tough diamond drill bits like our EASYGRES. However, although this type of drill bits will do the job on glazed tile and stoneware, they are not recommended for porcelain stoneware. It also will not burn out as easily as the masonry bits.Ĭarbide-tipped masonry drill bits, on the other hand, are probably the most common type of drill bits for drilling through tile. The first option, although a bit more expensive, is extremely durable and can bore through even the hardest tile surfaces, such as porcelain. Instead, opt for either diamond-tipped drill bits or carbide-tipped masonry drill bits. They are not strong enough to penetrate the hard surface of the tile. Not only are they not as efficient as new ones, but also the chances of damaging the surface of the tile increase dramatically if the drill bit isn’t performing at optimal capacity.Īdditionally, don’t use your regular drill bits for this task. Regardless of the material you’re trying to bore through, never use an old, worn out drill bit for tile.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |